Serving the Corpus Christi area  ·  (361) 600-9211  ·  Open Mon-Sun 7am-7pm
📞 (361) 600-9211 Free Quote

Metal Roofing in Robstown, TX (78380) · Local Professionals

Corpus Christi Metal Roofing · Fast response in Robstown and the Corpus Christi area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+347Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Robstown is a farm town where the roofs take a beating. The mix of older ranch homes, modest brick houses, and agricultural buildings around the Richard M. Borchard Regional Fairgrounds and along Highway 44 means we see a lot of worn shingles, rusted fasteners, and panels that have seen one too many hailstorms. Out here on the flat coastal plain, there is not much to block the wind, and that sea breeze carries salt and grit that works on metal and shingles alike.

Homeowners in Robstown (78380) call us because we know this area. We have worked on homes near the Nueces County Fairgrounds and along the streets off Main Street, and we understand how the heat, hail, and occasional tropical weather affect roofs here. We are fully insured and we show up when we say we will.

Metal Roofing in Robstown (78380)

Robstown sits on flat, sandy-to-clay soil that can hold water after a heavy rain, and many properties have shallow ditches or drainage swales that need to be considered when we stage materials and set up. The lots are often wide, which helps with access, but some of the older homes have mature mesquite and live oak trees that drop limbs and shade the roof, leading to moss and algae growth. Agricultural buildings and barns are common here, and they need roofing that can handle equipment traffic and the occasional hail without denting or leaking. We see a lot of low-slope roofs on these structures, and we know how to detail them so water sheds properly.

Our team has been serving Robstown and the surrounding Corpus Christi area for years. We have replaced shingles with standing seam and corrugated panels on homes near the Robstown Independent School District campuses, and we have repaired metal roofs on shops and sheds out toward the county line. We know the local suppliers and the permit office, and we can help you navigate the process.

Our services in Robstown

How a Job Works in Robstown

Step 1: You call us at (361) 600-9211 or fill out our contact form, and we schedule a free on-site assessment. We look at the roof, the attic if accessible, and the surrounding trees and drainage. We take photos and measurements, and we give you a written estimate with options.

Step 2: Once you approve, we pull the necessary permits from the City of Robstown and schedule the work. For homes with tight driveways or narrow side yards, we plan material delivery and staging carefully. If your property is in a historic district or has HOA design rules, we help you get the approval for panel profile and color before we order materials.

Step 3: After the work is done, we clean up thoroughly. We use magnets to pick up screws and nails, and we haul away all debris. We walk the roof with you, show you the finished work, and make sure you are satisfied before we leave.

Pricing in Robstown depends on the size and complexity of your roof, the material you choose, and the condition of the existing structure. For a typical 1,500 to 2,000 square foot home, metal roof installation starts at $8 per square foot, standing seam at $10, metal roof replacement at $9, and metal roof over shingles at $7. Corrugated and ribbed panel roofing starts at $5.50 per square foot, which is a popular choice for barns and shops. Repairs start at $450, and leak repairs also start at $450. Screw replacement and re-fastening starts at $750. We also offer coating and painting from $2.50 per square foot, and gutters from $9 per linear foot. Every roof is different, so call us at (361) 600-9211 for a free estimate tailored to your property.

My Robstown home has an old shingle roof with some hail damage. Can you install a metal roof over it?
Yes, we can often install a metal roof over your existing shingles if your roof structure is sound and your local code allows it. In Robstown, the code limits the number of layers, so we will check that during our free inspection. This can save you money on tear-off and disposal, and it adds an extra layer of protection. We will let you know if a full tear-off is a better option for your home.
A storm just blew through Robstown and lifted some panels on my barn. How quickly can you respond?
We prioritize storm damage calls in Robstown and the surrounding areas. Call us at (361) 600-9211, and we will schedule an inspection as soon as possible, often within 24 to 48 hours depending on demand. We can tarp or secure the roof to prevent further damage and provide a written estimate for repairs. We also help document the damage for your insurance claim.
What does a metal roof cost for a typical Robstown house?
For a standard 1,500 to 2,000 square foot home, most metal roof installations run between $12,000 and $20,000, depending on the material and complexity. Corrugated panel might be on the lower end, while standing seam or stone-coated steel is higher. Repairs are usually $450 to $1,500. We give you a detailed estimate after inspecting your roof, so you know exactly what to expect.
Do I need a permit to replace my roof in Robstown?
Yes, the City of Robstown requires a permit for roof replacements and some repairs. The requirements and fees vary, so we always check with the local building department before starting work. We handle the permit application for you and make sure the work meets current codes. If your home is in a historic district, there may be additional design review.
My neighbor and I are not sure where our property line is. Can you help with that when installing a new roof?
We are not surveyors, so we cannot determine property lines. However, we can work with you to ensure our work stays within your property. If there is a dispute, we recommend having a survey done. For HOA communities, we can coordinate with your HOA to get approval for the roof color and style before we order materials.
Are you insured for work on my Robstown property?
Yes, we are fully insured, carrying both general liability and workers' compensation insurance. This protects you and your property in the unlikely event of an accident.
How often should I have my metal roof inspected in Robstown?
We recommend an inspection every two to three years, and after any major storm. The heat, salt air, and occasional hail in Robstown can loosen fasteners and wear seals over time. A quick inspection can catch small issues before they become leaks. We offer free estimates for inspections and can set up a maintenance plan if you like.
Why choose us?

Trusted professionals in Corpus Christi

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Corpus Christi

All your work handled by qualified professionals in Corpus Christi

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

347+ Verified Client Reviews in Corpus Christi

⭐⭐⭐⭐⭐ 4.9/5 · 347 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Corpus Christi · Response within 24h · No commitment · ☎ (361) 600-9211

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Corpus Christi ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm