Serving the Corpus Christi area  ·  (361) 600-9211  ·  Open Mon-Sun 7am-7pm
📞 (361) 600-9211 Free Quote

Metal Roofing in Beeville, TX (78102) · Local Professionals

Corpus Christi Metal Roofing · Fast response in Beeville and the Corpus Christi area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+347Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Beeville runs on ranch land and oil field traffic, and the roofs here take a beating that coastal folks a few miles east never see. Most homes around the Bee County Courthouse and along Washington Street are older single-story ranches and farmhouses with low-pitch shingle roofs, plus a growing number of metal barns and shop buildings out on the county roads. When the summer sun hits 100 degrees and a blue norther rips through in February, that old shingle roof shows every year of its age.

We are Corpus Christi Metal Roofing, and we make the drive up Highway 181 to Beeville (78102) because we know this brush country. From the courthouse square to the rodeo grounds, we have seen how wind and heat separate seams, back out screws, and leave flashing gaps that leak right into your living room. If your roof is telling you it is tired, call us at (361) 600-9211.

Metal Roofing in Beeville (78102)

Beeville sits on the coastal plain but feels more like brush country: sandy loam over clay, mesquite and huisache roots that push up sidewalks, and lots that range from tight in-town parcels near the high school to wide-open acreage out on FM 351. The housing stock is mostly 1950s to 1980s brick and frame ranches with low-slope composition roofs, and those low slopes are exactly where wind-driven rain finds a way in. Add in the metal shop buildings and hay barns scattered across Bee County, and you get a mix of residential and agricultural work that demands different fasteners, different panel profiles, and a crew that understands how to handle a roof on a building that was never designed for a shingle tear-off.

Our team has worked roofs from Corpus Christi to Beeville and all points in between. We know that a metal roof here has to handle intense UV, summer thunderstorms that drop two inches in an hour, and the occasional hurricane-spawned wind that peels back panels like paper. We also know the local building department in Beeville has its own permit thresholds and inspection schedule, and we pull the right permits before we ever set a ladder.

Our services in Beeville

How a Job Works in Beeville

Step 1: You call (361) 600-9211 or fill out our form, and we schedule a free on-site assessment. We walk the roof, check the decking, look at the flashing and fasteners, and talk to you about what we find. No pressure, no sales pitch. If a repair will do, we tell you that.

Step 2: Once you approve the estimate, we order materials and pull the permit from the City of Beeville if one is required. On the work day, our crew arrives early, protects your landscaping and driveway, and gets to work. On tighter in-town lots near the courthouse, we use a conveyor or a crane to get panels up without tearing up your fence or your neighbor's shrubs. If your home is in a historic district or under an HOA, we coordinate the paperwork and color approval before we order a single panel.

Step 3: When the last screw is set, we magnet-sweep the yard for nails and metal shavings, haul off all old roofing debris, and walk the job with you. We do not leave until you have seen every detail and signed off. Our team treats your property like it belongs to a neighbor, because in Beeville it probably does.

Metal roofing in Beeville is priced by the square foot, and the numbers depend on the panel type, the pitch of your roof, how many layers are already there, and how easy it is to get materials to the roof. For a basic corrugated or ribbed panel roof, you are looking at around $5.50 per square foot installed. Standing seam runs about $10 per square foot, and a full metal roof replacement starts around $9 per square foot. If you are retrofitting metal over existing shingles, that starts at $7 per square foot. Repairs and leak fixes start at $450, screw replacement and re-fastening at $750, and flashing or skylight repair at $600. We give free estimates, so call (361) 600-9211 and we will give you a real number for your Beeville property, not a guess.

My house is near the Bee County Courthouse and has an old low-slope shingle roof. Can you install metal without tearing off the old shingles?
Yes, in many cases we can install a metal roof over your existing shingles using a retrofit system, as long as your roof structure can handle the added weight and your local code allows it. Beeville follows standard building codes that limit the number of layers, so we will check the deck and the existing layers during our free inspection and tell you honestly whether a retrofit or a full tear-off is the right call.
A storm just blew through Beeville and lifted some panels on my barn. How fast can you get out there?
We prioritize storm and wind damage calls. Call us at (361) 600-9211, and we will schedule a free inspection as soon as possible, usually within a day or two depending on how widespread the damage is. We can tarp or secure the roof temporarily to prevent further water damage, then give you a repair estimate.
What does a typical metal roof replacement cost for a 2,000 square foot ranch house in Beeville?
For a 2,000 square foot ranch with a low-slope roof, a basic corrugated panel installation might run around $11,000 to $13,000, while a standing seam roof could be $18,000 to $22,000. The exact price depends on the pitch, the number of penetrations, whether we need to replace decking, and the panel profile you choose. We give free estimates with a firm price before any work starts.
Do I need a permit from the City of Beeville to replace my roof?
Roofing permits are commonly required for a full replacement or re-roof in Beeville, and the thresholds and fees are set by the local building department. We handle the permit application and inspections for you as part of the job. Rules can change, so we always verify the current requirements with the City of Beeville before we start.
My neighbor's tree branches hang over my property line and scrape my roof. What can I do?
In Texas, you generally have the right to trim branches that cross onto your property, but you should not damage the tree or trespass to do it. If the branches are causing wear on your roof, we can inspect and document the damage for your records. If you are in an HOA, check the rules first, and we are happy to coordinate with your neighbor or HOA to make sure the roof installation goes smoothly.
Are you fully insured for roofing work in Beeville?
Yes, we are fully insured with general liability and workers' compensation coverage. That protects you and your home if anything goes wrong on the job.
What should I do to maintain my metal roof in Beeville between seasons?
Beeville's heat and wind mean you should check your roof twice a year, once in spring before storm season and once in fall. Look for loose or backed-out screws, debris in valleys, and any signs of rust or sealant failure around flashing. We offer free inspections and can replace screws and re-seal penetrations to keep your roof tight. Call (361) 600-9211 to schedule a maintenance check.
Why choose us?

Trusted professionals in Corpus Christi

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Corpus Christi

All your work handled by qualified professionals in Corpus Christi

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

347+ Verified Client Reviews in Corpus Christi

⭐⭐⭐⭐⭐ 4.9/5 · 347 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Corpus Christi · Response within 24h · No commitment · ☎ (361) 600-9211

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Corpus Christi ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm